Epoxy system

DESCRIPTION:
Epoxy system for flooring is intended for concrete surfaces on metallic structures and plants used in the food, chemical, petro-chemical, paper, weapons industries for protection and decoration.


QTEK Epoxy enamel, 2k in thick coat (S3024)

BENEFITS:

  •    Available in a wide range of RAL colors
  •    High durability and flexibility
  •    Good support adherence
  •    Good resistance to abrasion, corrosive chemical agents, water and solvents
  •    Resistance over time
     

APPLICATION:
With compressed air spray gun, air-mix, air-less, brush, roller. Prior to use the product is conditioned at 18-25 ° C and homogenized in the original package. Ad component II – hardener l 3024 according with the blending ratio: 100 parts enamel S 3024/ 25 parts hardener I 3024.
Hardener I 3024 will be added slowly, under stirring to component I. Provide for good homogenization of the two components.
Pre-reaction time is 30 minutes. Optimum application interval is between 30 minutes and 4 hours from components blending. At temperatures higher than 25°C pot life of blend might decrease down to 2 hours.



Blend will be thinned with THINNER D006-50 max. 20% if applied by spraying to a flow time of 20-24 seconds determined with cup of Φ 4mm. Blend will be applied unthinned or thinned up to 10% if applied by brushing or rolling. Optimum application interval between coats: minimum 24 hours.
Do not apply on fresh concrete surfaces that are properly cured or on wet surfaces.

SPREADING RATE: 1 kg blend (enamel S 3024 + hardener I 3024) can cover 5 sqm of concrete surface in one coat or 6-8 sqm of metallic surface in one coat. If applied on concrete consumption varies according to the nature of the surface.
DRYING TIME: 24 hours at 23°C. Surface can be used 7 days after last coat was applied (at least 4 days from total drying).
PACKING: 20 kg
 

QTEK Two packs Epoxy primer, in thick coat (S3024)

BENEFITS:

  •    Improves the characteristics of the concrete (resistance, durability, etc.)
  •    Provides a good adherence of coats of enamel coats, subsequently applied
  •    Reduces the ENAMEL consumption, subsequently applied
  •    Extends the service life of the system
  •    Easy to apply
     

APPLICATION:
With brush, roll for impregnation, primering prior to painting with Qtek Epoxy enamel 2k in thick coat (S3024). Prior to use the product is conditioned at 18-25 ° C and homogenized in the original package.
Add component II – hardener I 3024, according with the blending ration: 100 parts primer S 3024/ 25 parts hardener I 3024.
Hardener I 3024 will be added slowly under stirring to component I. The optimal homogenization of the two components will be considered.

Pre-reaction time is 30 minutes. Optimum application interval is between 30 minutes and 4 hours from after blending the components.
In the course of application, it is intended that the product is best impregnated in the concrete surface so that after drying the appearance of the obtained surface is matte.

Do not apply to fresh uncured concrete surfaces or wet surfaces. The optimum re-coating time after application of the primer coat is 24 hours.
SPREADING RATE: 1 kg blend (primer S 3024 + hardener I 3024) can cover 4-6 sqm of concrete surface in one coat. If applied on concrete, consumption varies according to its nature.
DRYING TIME: 24 hours at 23°C
PACKING: 20 kg

NEWSLETTER
SUBMISSION
* In accordance with the GDPR, applicable from May 25, 2018, subscription involves
your explicit consent to the processing of your data for own purpose, for sending newsletters.
Contact Information
Constructorilor Boulevard, No. 1-3, Timisoara 300571, Romania
tel: 0040-256-222139
fax: 0040-256-222179